TRANSITIONS

GET SET

GET SET POSTER DESIGN
GET SET POSTER DESIGN
press to zoom

CONCEPT

Purchase  GET SET Poster

GET SET is the tense moment that follows your start position, where the mind instructs the body to move into position before the signal to take off. The thought of turning back at this moment, diminishes.

 

GET SET is captured in a full action pose with a one track mind, awaiting the signal to GO!  All other Triathletes disappear as all ambient sound fades away, the focus in internal, the moment is quiet until, GO!

 

GET SET is part of an overall composition of figures called THE SWIMMERS.  Totaling 5 in all, THE SWIMMERS reflect the first stage of competition within a Triathlon event.  The swim stage is full of preparation, reflection and emotion.

 

I wanted each figure to express the various states of mind before entering the water.  Each state transitions into the next in a successive fashion.

 

 

Measurements: 

3 3/4 feet Height by 3 feet Width 

 

Materials:

Winterstone, Stainless Steel,  Cement, Paint

(Click image to expand)

GET SET process 01
GET SET process 01

Technical Drawing

press to zoom
GET SET process 02
GET SET process 02

Maquette stage

press to zoom
GET SET process 03
GET SET process 03

Model Photography

press to zoom
GET SET process 04
GET SET process 04

Monument Sculpting

press to zoom
GET SET process 05
GET SET process 05

Monument Casting

press to zoom
GET SET process 06
GET SET process 06

Monument Finishing

press to zoom

DRAWING

SCULPTING

MAQUETTE

CASTING

MODEL

FINISHING

STAGES

DRAWING

The Process is an extensive one.  Involving Drawing, Sculpting and Painting.  Consisting of trial and error when working out the full composition, sculpting of body posture, anatomy, correct symbolic clothing, material, production and installation.  The first stage was moving the idea from concept to reality.  This involves the process of Drawing.

 

GET SET is a figure symbolizing the motions of a quiet storm.  The PENSIVE thoughts, the CONFIDENT affirmations, the coiling readiness of ON YOUR MARK has now transitioned into this moment.  This is the last step before the full commited action of competing.

 

GET SET's body posture is the resulting actions that follows ON YOUR MARK.  Her arms seeking position amongst her fellow Triathletes, clearing a path of entry for herself.  Body prepped for one action, which is to GO!  GET SET is poised for commitment and competition.

MAQUETTE

Following a conceptual Drawing, the next step was developing a Maquette.  This Maquette would be a fully materialized version of conceptual idea of GET SET, sculpted to reflect the intended composition, arrangement and supporting elements.   This sculpted Maquette becomes the dimentional representation of my concept, allowing me to understand what the projected cost and build time will be for the final monumental version.

 

​GET SET, started as a concept, evolving into a Drawing, is now materialized as a Maquette.  Made of oven baked clay with an underwire frame, she is painted to reflect the intended look and feel of the Monument version.  She has been designed, sculpted and built to include magnets within her base, which allows me to further tweek her position in the overall composition.

MODEL

Following the Maquette, I am now comfortable with moving into the stage of the monument size scuptural process.  Since the monumental size sculpture requires costly time, material and energy, knowing that I worked out all my concepts in the Maquette give me the freedom to make creative adjustments without sacrificing or second guessing the conceptual foundation.

 

I seek out a model to represent GET SET.  Within my circle of friends I chose an inspirational Persona, Manager, Wife and Mother.  By preping her on the feeling and meaning of GET SET, we went through a variety of poses and settled on a version of the Maquette's pose.  Arms leading her intended path, head forward, ready to react to the signal representing the begining of her race group.

 

I photographed her with my smartphone, making sure to gather enough photo reference for details of her face and body.  These results allows me to combine my knowledge of figure sculpting, anatomy and the photo reference into the Monument of GET SET I envision.

SCULPTING

The following is the sculpting process of Monument GET SET.  Starting with the underline structure of a wire frame.  This heavy wire  allows me to first, create a anatomically correct supporting frame for the clay, second allows for further ajustment to the body composition by bending during any phase of the sculpting process.

 

Through various stages of the sculpting process I discover the true strength and balance of the pose, serving as a physicological foundation to the sculpture, this allows me to further refine the form and the details of the sculpture.  Slowly building up the anatomical forms, I switch between my large sculpting tools to the smaller tools while working into the details.  Working over a few days, and long hours, I execute the GET SET Monument with confidence and determination.  Also being very mindful of my schedule, as I have the other elements of Transitions thorugh Triathlon to produce.

 

GET SETsculpting 01
GET SETsculpting 01
press to zoom
GET SETsculpting 02
GET SETsculpting 02
press to zoom
GET SETsculpting 03
GET SETsculpting 03
press to zoom
GET SETsculpting 04
GET SETsculpting 04
press to zoom

(Click image to expand)

The Process of Casting is both extensive and laborous.  It is technical process involving knowledge of material chemestry, temperature, timing and patience.  At any moment, a wrong decision or neglect can result in extending the process or ruining your sculpture, so paying attention to the process is very important.  I was assisted by casting technicians for my project.  Parts of the process was done by the tech, others my myself and others together as a team.

 

The Process involves first making a mold.  For this sculpture, I've decided to make a 'waste mold'  due to time and cost effective materials.  A 'Waste Mold' is a mold that is destroyed and discarded during the casting process allowing for one unique copy of the sculpture. 

 

Plaster was mixed then applied to the sculpture, sectioned by thin sheet of metal called 'shims'.  The Plaster will cover the entire sculpture with a measure of 2/3rds thickness.  Bendable Metal bars are attached using Burlap dipped into the Plaster Mix.  When both the Plaster, and burlapped bars are dried, this becomes the 'Waste Mold' of the sculpture.  This mold is pulled apart in its shimmed sections then cleaned from the inside negative area, removing excess clay from the original sculpture.

CASTING

GET SET Casting 01
GET SET Casting 01
press to zoom
GET SET Casting 02
GET SET Casting 02
press to zoom
GET SET Casting 03
GET SET Casting 03
press to zoom
GET SET Casting 04
GET SET Casting 04
press to zoom

(Click image to expand)

WELDING

Once the entire inside negative of the 'Waste Mold' is cleaned, the process of filling the mold can begin.  I will first allow the mold to fully air dry and I will take this opportunity to  create the metal supporting frame for the Monument.  This involves accurate measurements and welding of metal.  I am assisted by a Welding Tech for the cutting, measuring, bending, welding and grinding of this process.  The resulting form is a strong underlining Metal structure for my monumental GET SET sculpture.

THE FILL

Now that the supporting frame and the 'Waste Mold' is fully dry, the process of filling the mold can begin.  First the mold must be prepared for filling by applying Schelac and a separating agent to its negative layer.  Wax Paste is used to cover the entire negative layer, head to toe.  This separator will allow the Plaster mold to not adhere to the Winterstone material being used to fill the mold.  Winterstone, a cousin of both Plaster and concrete, has the ability to achieve the sculptural detail of Plaster with the strength of Concrete.

 

Now that the schelac and wax paste is applied to all areas of the negative mold, the mixing of the waterbased Winterstone starts.  The instructions calls for measurements of water to different measurements of winterstone in addition to fiberglass material.  Gloves and Masks are worn for safety reasons.

 

Once the first and second layers of Winterstone are applied, the metal frame is inserted into the largest section of the 'Waste Mold' and adhered to it using Winterstone and fiberglass strands.  Each section is fused piece by piece until the entire mold is fused together as one mold.  The Mold is left to dry  then the process of removing the 'Waste Mold' is performed.

 

Removing the 'Waste Mold' involves a hammer and chisle, chisling away the mold piece by piece in small, medium and large chunks until the underline copy is revealed.  Extra care must go into the technique of how the mold is chisled away, making sure one does not chisel too far beyond the mold and hitting the winterstone material.  Losing valuable detail such as ears, nose or fingers can result in the lost of valuable time being used for repairs.

 

The 'Waste Mold' is now removed and discarded, revealing the Winterstone copy/ version of GET SET.  The detailed areas will require extra care to remove smaller fragments of the 'Waste Mold' using picks and smaller chisles.  After the figure is clean and prepared, it will move into the final Finishing stage.

FINISHING

Using my GET SET Maquette as referrence, I know exactly what exterior finish I want to produce for the Monument GET SET.  A variety of outdoor paints and weatherproof sealant was choosen for the finish.  First, a coat of black paint is used for the under-coat, so when I apply the bright swimcap colors they will pop during observation.  After the under-coat of black paint is applied, the swimsuit black, skintone gold, and details of the timing chip, goggles and swimcap are painted. The final touches go to the watch and lines of detail within the swimsuit design.

 

Once the paint is dried, the figure is coated with weatherproof sealant.  I perform three coats of the sealant as I reminder of what Hurricane Sandy did to our city.

INSTALLING

Installing GET SET and the other elements of Transitions through Triathlon at the Riverside Park South location was met with traffic and rain.  Due to these challenges the installation was carried over into a second day.  The Base Frame went into the ground first, firmly attached to the site with bolts and spot welds.  Next the Arch was installed, using a hoist, rope, scafolding and spot welding.  

 

Then  the following day, GET SET along with the other cast of SWIMMERS, CYCLISTS, RUNNER and VICTORY were spot welded to the Base Frame.  Finally the day of completion has come.  The last weld was met with a small applause by myself and the installation crew.

Transitions through Triathlon